One Control Minimal Series Pedal Board Junction Box w/ BJF Buffer
One Control Minimal Series Pedal Board Junction Box with BJF Buffer OC-M-JBBUF
One Of The Most Natural-Sounding Buffer Circuits Ever Created
Every pedalboard needs a tool like this – a small box with two inputs and two outputs which is very simple, but makes a tremendous difference in your sound. With the One Control Minimal Series Pedal Board Junction Box with BJF Buffer OC-M-JBBUF the pedalboard itself is like one big effects pedal, just connect the cable from the guitar to the Pedal Board Junction Box, and from the Pedal Board Junction Box to the amplifier, and the setup is complete!
If there is a buffer in the input part of the pedalboard, you can limit any change in your signal due to cable length, patch cables, and the connections following the input. You can also use it as an output buffer instead of on the input. This amazing circuit is installed in many switchers from One Control and is one of the most natural-sounding buffer circuits ever created that destroys the old image people have from using old buffer circuits that changed the tone of the instrument.
The POLARITY/REVERSE switch is used to restore phases that may be inverted depending on the characteristics of the equipment or to match the phases of other parts. This logic may be confusing, but don’t worry - make a sound with the band at rehearsal and set it to the one that can be heard better. Just by itself, the "out of sound" and "power of sound" of the whole band will change.
The Pedal Board Junction Box with BJF Buffer has input and output on the top of the enclosure, so you can use it without wasting any space on the pedalboard. When the input is overloaded, it will not degrade the output tone.
Created at the request of many of the world’s greatest guitarists by Björn Juhl, one of the greatest amp and effects designers in the world, the BJF Buffer is the answer to keeping your tone pristine in all sorts of signal chains, from the stage to the studio.
The more effects that are connected, the stronger the effect when the buffer is connected earlier in the chain and it’s more effective. This is the reason for incorporating the BJF Buffer into the input part. By turning on the BJF Buffer, you can stabilize your base tone to a warm and natural sound. You can also use it as an output buffer depending on the characteristics of the effects in your pedalboard chain.
Features of the Pedal Board Junction Box:
- Precise Unity Gain setting to 1
- Input impedance will not change the tone
- Will not make output signal too strong
- Ultra-low noise output
How to use the One Control Minimal Series Pedal Board Junction Box:
- BUFFER/PASSIVE SWITCH: TURNS THE BUFFER ON/OFF. In PASSIVE mode, the buffer is turned off. IF YOU DON'T CONNECT THE POWER, USE PASSIVE MODE.
- POLARITY/REVERSE SWITCH: INVERSES THE PHASE BETWEEN THE BUFFER IN/BUFFER OUT JACKS. THIS SWITCH ONLY WORKS WHEN THE BUFFER/PASSIVE SWITCH IS ON THE BUFFER SIDE.
- 9V IN: Connect the power adapter. We use a standard center minus DC9V terminal. Be sure to connect the power supply when using the buffer. When the power supply is connected successfully, the center LED lights up.
- When Buffer is OFF, both A and B terminals can be connected from any direction you like.
- When Buffer is ON, the terminal on the A side always enters from BUFFER IN and connects so that a signal comes out from BUFFER OUT.
Specifications of the One Control Minimal Series Pedal Board Junction Box with BJF Buffer:
- Dimensions: 94D×46W×40H mm
- Weight: 220g
- Input Impedance:500kΩ (Buffer ON)
- Output Impedance:60Ω (Buffer ON)
- Current Draw:3mA
- Power: DC9V negative tip 2.1mm barrel type
Make'n Music is proud to be an authorized dealer, as well as the USA Shipping Warehouse for One Control products. Best Selection always in stock and for sale at a great price.
SKU: | 818996015997 |
Serial Number: | 818996015997 |
MPN: | 818996015997 |
One Control Minimal Series Pedal Board Junction Box with BJF Buffer OC-M-JBBUF
One Of The Most Natural-Sounding Buffer Circuits Ever Created
Every pedalboard needs a tool like this – a small box with two inputs and two outputs which is very simple, but makes a tremendous difference in your sound. With the One Control Minimal Series Pedal Board Junction Box with BJF Buffer OC-M-JBBUF the pedalboard itself is like one big effects pedal, just connect the cable from the guitar to the Pedal Board Junction Box, and from the Pedal Board Junction Box to the amplifier, and the setup is complete!
If there is a buffer in the input part of the pedalboard, you can limit any change in your signal due to cable length, patch cables, and the connections following the input. You can also use it as an output buffer instead of on the input. This amazing circuit is installed in many switchers from One Control and is one of the most natural-sounding buffer circuits ever created that destroys the old image people have from using old buffer circuits that changed the tone of the instrument.
The POLARITY/REVERSE switch is used to restore phases that may be inverted depending on the characteristics of the equipment or to match the phases of other parts. This logic may be confusing, but don’t worry - make a sound with the band at rehearsal and set it to the one that can be heard better. Just by itself, the "out of sound" and "power of sound" of the whole band will change.
The Pedal Board Junction Box with BJF Buffer has input and output on the top of the enclosure, so you can use it without wasting any space on the pedalboard. When the input is overloaded, it will not degrade the output tone.
Created at the request of many of the world’s greatest guitarists by Björn Juhl, one of the greatest amp and effects designers in the world, the BJF Buffer is the answer to keeping your tone pristine in all sorts of signal chains, from the stage to the studio.
The more effects that are connected, the stronger the effect when the buffer is connected earlier in the chain and it’s more effective. This is the reason for incorporating the BJF Buffer into the input part. By turning on the BJF Buffer, you can stabilize your base tone to a warm and natural sound. You can also use it as an output buffer depending on the characteristics of the effects in your pedalboard chain.
Features of the Pedal Board Junction Box:
- Precise Unity Gain setting to 1
- Input impedance will not change the tone
- Will not make output signal too strong
- Ultra-low noise output
How to use the One Control Minimal Series Pedal Board Junction Box:
- BUFFER/PASSIVE SWITCH: TURNS THE BUFFER ON/OFF. In PASSIVE mode, the buffer is turned off. IF YOU DON'T CONNECT THE POWER, USE PASSIVE MODE.
- POLARITY/REVERSE SWITCH: INVERSES THE PHASE BETWEEN THE BUFFER IN/BUFFER OUT JACKS. THIS SWITCH ONLY WORKS WHEN THE BUFFER/PASSIVE SWITCH IS ON THE BUFFER SIDE.
- 9V IN: Connect the power adapter. We use a standard center minus DC9V terminal. Be sure to connect the power supply when using the buffer. When the power supply is connected successfully, the center LED lights up.
- When Buffer is OFF, both A and B terminals can be connected from any direction you like.
- When Buffer is ON, the terminal on the A side always enters from BUFFER IN and connects so that a signal comes out from BUFFER OUT.
Specifications of the One Control Minimal Series Pedal Board Junction Box with BJF Buffer:
- Dimensions: 94D×46W×40H mm
- Weight: 220g
- Input Impedance:500kΩ (Buffer ON)
- Output Impedance:60Ω (Buffer ON)
- Current Draw:3mA
- Power: DC9V negative tip 2.1mm barrel type
Make'n Music is proud to be an authorized dealer, as well as the USA Shipping Warehouse for One Control products. Best Selection always in stock and for sale at a great price.
SKU: | 818996015997 |
Serial Number: | 818996015997 |
MPN: | 818996015997 |
One Control Minimal Series Pedal Board Junction Box with BJF Buffer OC-M-JBBUF
One Of The Most Natural-Sounding Buffer Circuits Ever Created
Every pedalboard needs a tool like this – a small box with two inputs and two outputs which is very simple, but makes a tremendous difference in your sound. With the One Control Minimal Series Pedal Board Junction Box with BJF Buffer OC-M-JBBUF the pedalboard itself is like one big effects pedal, just connect the cable from the guitar to the Pedal Board Junction Box, and from the Pedal Board Junction Box to the amplifier, and the setup is complete!
If there is a buffer in the input part of the pedalboard, you can limit any change in your signal due to cable length, patch cables, and the connections following the input. You can also use it as an output buffer instead of on the input. This amazing circuit is installed in many switchers from One Control and is one of the most natural-sounding buffer circuits ever created that destroys the old image people have from using old buffer circuits that changed the tone of the instrument.
The POLARITY/REVERSE switch is used to restore phases that may be inverted depending on the characteristics of the equipment or to match the phases of other parts. This logic may be confusing, but don’t worry - make a sound with the band at rehearsal and set it to the one that can be heard better. Just by itself, the "out of sound" and "power of sound" of the whole band will change.
The Pedal Board Junction Box with BJF Buffer has input and output on the top of the enclosure, so you can use it without wasting any space on the pedalboard. When the input is overloaded, it will not degrade the output tone.
Created at the request of many of the world’s greatest guitarists by Björn Juhl, one of the greatest amp and effects designers in the world, the BJF Buffer is the answer to keeping your tone pristine in all sorts of signal chains, from the stage to the studio.
The more effects that are connected, the stronger the effect when the buffer is connected earlier in the chain and it’s more effective. This is the reason for incorporating the BJF Buffer into the input part. By turning on the BJF Buffer, you can stabilize your base tone to a warm and natural sound. You can also use it as an output buffer depending on the characteristics of the effects in your pedalboard chain.
Features of the Pedal Board Junction Box:
- Precise Unity Gain setting to 1
- Input impedance will not change the tone
- Will not make output signal too strong
- Ultra-low noise output
How to use the One Control Minimal Series Pedal Board Junction Box:
- BUFFER/PASSIVE SWITCH: TURNS THE BUFFER ON/OFF. In PASSIVE mode, the buffer is turned off. IF YOU DON'T CONNECT THE POWER, USE PASSIVE MODE.
- POLARITY/REVERSE SWITCH: INVERSES THE PHASE BETWEEN THE BUFFER IN/BUFFER OUT JACKS. THIS SWITCH ONLY WORKS WHEN THE BUFFER/PASSIVE SWITCH IS ON THE BUFFER SIDE.
- 9V IN: Connect the power adapter. We use a standard center minus DC9V terminal. Be sure to connect the power supply when using the buffer. When the power supply is connected successfully, the center LED lights up.
- When Buffer is OFF, both A and B terminals can be connected from any direction you like.
- When Buffer is ON, the terminal on the A side always enters from BUFFER IN and connects so that a signal comes out from BUFFER OUT.
Specifications of the One Control Minimal Series Pedal Board Junction Box with BJF Buffer:
- Dimensions: 94D×46W×40H mm
- Weight: 220g
- Input Impedance:500kΩ (Buffer ON)
- Output Impedance:60Ω (Buffer ON)
- Current Draw:3mA
- Power: DC9V negative tip 2.1mm barrel type
Make'n Music is proud to be an authorized dealer, as well as the USA Shipping Warehouse for One Control products. Best Selection always in stock and for sale at a great price.
SKU: | 818996015997 |
Serial Number: | 818996015997 |
MPN: | 818996015997 |